little quilted star ornaments – Monday Morning Designs

Lately I’ve been going through my fabric trying to find a good use for leftovers. So far I’ve made my colorful, controlled scrappy Five Squared Quilt and my Four Patch Charm quilt, made with a ray of lovely golden yellows.

Even with those two completed, I still have fabric left from other projects. Three years ago I made my son a tree skirt for Christmas using a mix of beautiful metallic fabrics by Marcus Brothers, RJR and Andover Fabrics. And…

while scrolling through Pinterest I found a great idea for using smaller scraps, little quilted star ornaments. Right away I knew these metallics would be a perfect choice for this project.

Since I only saw a photo and the dimensions weren’t given, I experimented until I had made one small enough without using exceptionally tiny pieces. I also decided to make a tutorial because other quilters may be looking for a fun way to use up little scraps, and just in time for the holidays. So here it is…

Materials needed to make one 4 ½” x 4 ½” star ornament:

For Star: Gold fabric – (1) 2 ½” x 14 ½” strip
Subcut (1) 2 ½” x 2 ½” square and (8) 1 ½” x 1 ½” squares

For Star: White fabric – (1) 2 ½” x 14″ strip
Subcut (4) 1 ¾” x 2 ½” rectangles and (4) 1 ¾” x 1 ¾” squares

For Backing: Gold fabric – (1) 5 ½” x 5 ½” square

For Interfacing: Pellon Fusible Fleece – (1) 4 ½” x 4 ½” square

For ¾” Bias tape binding: Gold fabric – (1) 1 ¼” x 20″ strip (approximate)

For Hanger: White ribbon – (1) 7″ piece (or material of your choice)

Once the fabric is cut, draw a diagonal line on the back of all the gold 1 ½” squares. As though making a flying geese unit, sew two 1 ½” x 1 ½” gold squares to the top corners of a 1 ¾” x 2 ½” white rectangle, attaching them to the 2 ½” side. Make 4.

Next, lay out squares and sewn units with the 2 ½” sides facing toward the center, as shown below. Sew together to make rows. Press the top and bottom row seams toward the outer squares. Press the middle row seam toward the center square.

Sew the rows together to complete the star; seams will nest. Press seams open. Trim block to 4 ½” x 4 ½” square making sure to leave a ¼” all the way around.

Trim any threads off the back to prevent them from showing through to the front. This is always a good rule to follow. 🙂 Next, adhering the interfacing. I used 987F Pellon fusible fleece because of the low loft, yet there’s enough to give some depth when quilted.

I always put a scrap piece of fabric over my projects to prevent any adhesive from getting on my iron.

Once the fusible fleece is adhered, sandwich the star unit to the backing. The backing square will be a bit bigger to allow for shifting when quilting.

With a hera marker, I marked the first two lines to be quilted then I used straight pins to hold the pieces together. After the first lines were finished, I removed the pins.

I chose a different quilting pattern for each one. I really like how they turned out!

Once your blocks are quilted, it’s time for binding. Since the ornaments are small, and to reduce bulk, I made bias tape using a ¾” bias tape maker. (If you don’t have one, they can be purchased at most sewing stores inexpensively or you can buy bias tape already made). You’ll need enough to go around all four sides including a few inches extra.

Once made, press the bias tape in half lengthwise before sewing it on; that’ll help to keep it even on each side. I sewed mine on by hand (each side, one at a time) which was easier than trying to line everything up and sew through all the layers at once.

One the binding is attached, the last thing to do is add a hanger. There are a lot of options here…you can use jute, ribbon, cording—whatever you like. I used a lovely white ribbon I had on hand. I looped it and tacked the ends together before stitching it on.